HVAC Ductwork/Sheet Metal Tools- Basics, Uses, & Demonstration of Each!

Share it with your friends Like

Thanks! Share it with your friends!

Close

In this HVAC Ductwork Video, I go over the Common HVAC Sheet Metal Tools Used in the Field and I Give a Demonstration of each, as well as how often I use each of them. I mention other tips while using these tools and a description of the common practices! Each of the tools is linked in this description section!

Supervision is needed by a licensed HVAC Tech while doing this as Experience and Apprenticeship garners Wisdom and Safety.

These Videos are all part of our Training Series on HVACR Service, Installation, Preventative Maintenance, General Knowledge, and Tips. Please comment and ask for videos that you would like to see in the future! We come out with new videos every few days from my job sites, service calls, and the training shop! I hope you enjoy and find them very beneficial! See you next time at ACSERVICETECH Channel!

Check out All of the ACSERVICETECH Playlists- https://www.youtube.com/channel/UCOZR-1IqsAer9wzlvFgb4mA/playlists?view_as=public

If you want to support the ACSERVICETECH Channel and receive more HVAC content, check out www.Patreon.com/acservicetech

ACSERVICETECH is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.
You can enter Amazon through this http://amzn.to/2aenwTq

Here is the link for the Malco Combination snips with 3″ long mouth- http://amzn.to/2wuft2L

Here is the link for the Wiss Cable Tie Tensioning Tool- http://amzn.to/2wtYL3D

Here is a link to the Malco Snap Lock Punch http://amzn.to/2cY53Ag

Here is a link to the Wiss 3 Pack Tin Snips http://amzn.to/2bHWhWO

Here is the link for the Wiss Bulldog Snips- http://amzn.to/2x1BeIY

Here is a link to the Wiss 5 Blade Crimper http://amzn.to/2bwTlsW

Here is a link to the Wiss Hand Seamers http://amzn.to/2dRk83v

Here is a link to the Midwest Upright 90 Degree Right Hand Tin Snip- http://amzn.to/2x1TfGZ

Here is a link to the Midwest Upright 90 Degree Left Hand Tin Snip- http://amzn.to/2iSwpvc

Here is the link for the Wiss 12″ Folding Tool- http://amzn.to/2xGqb52

Here is the link for the Wiss 18″ Folding Tool- http://amzn.to/2wx8y7v

Here is the link for the Wiss 24″ Folding Tool- http://amzn.to/2wu6DCg

Here is the link to the Klenk 20oz Sheet Metal Hammer- http://amzn.to/2wxzTpY

Here is the link for the Malco FDC1 Flex Cutting Tool- http://amzn.to/2wwNrlv

Here is the link for the Klein 7/8″ Step Drill Bit- http://amzn.to/2xGQVSQ

Here is the link to the Dewalt 1/4″ magnetic bit drivers- http://amzn.to/2x1V073

Here is the link to the Dewalt 5/16″ magnetic bit drivers- http://amzn.to/2vUYLWV

Here is the link for the Malco Sheet Metal Scribe- http://amzn.to/2eunoU0

Here is the Link for the Malco Dividers for Making Circles- http://amzn.to/2xGN6go

Here is the Link for the Malco Notchers- http://amzn.to/2iRTrlH

Here is the link to the Malco Scratch Awl- http://amzn.to/2vUvmfy

Here is the Link for the Malco HC1 Adjustable Collar Cutter for Drill- http://amzn.to/2vBHxlU

Here is a link to the JB 6 CFM Vacuum Pump http://amzn.to/2nqbvo8

Here is the Link to the Appion Red 3/8″ to 1/4″ Vacuum Hose- http://amzn.to/2uYg6Ro

Here is the link to the Appion Valve Core Removal Tool- http://amzn.to/2uYr8WL

Here is the link to the Yellow Jacket 1/4″ by 1/4″ heavy duty hose straight- http://amzn.to/2umtcod

Here is the link to the CPS Vacuum Micron Gauge- http://amzn.to/2v1nM3O

Here is a link for RectorSeal Bubble Gas Leak Detector http://amzn.to/2ckWACn

Here is a link to the UEI DL389 Multimeter used in the videos- http://amzn.to/2xAdaJf

Here is the link to the Fieldpiece ST4 Dual Temp Meter- http://amzn.to/2wc1ME3

Here is a link to the Air Acetylene Torch setup- http://amzn.to/2aQalsb

Here is a link to the 15% Silver Brazing Rods- http://amzn.to/2gVLyLc

Here is a link the Nitrogen Regulator http://amzn.to/2bXdR5f

Here is a link to the Nitrogen Flow Meter http://amzn.to/2brvoBg

Here is a link to the Digital Refrigerant Scale used in the video
http://amzn.to/2b9oXYl

Here is the Link for the Yellow Jacket Refrigerant Manifold Gauge Set used in the videos http://amzn.to/2aenwTq

Here is a link to Refrigerant hoses with valves used in the videos http://amzn.to/2aBumVI

Here is the link for the Imperial Kwik Charge 535-C- http://amzn.to/2uipEI6

Thank You,
ACSERVICETECH

Comments

AC Service Tech LLC says:

Tool List- https://www.amazon.com/shop/acservicetech
Support- https://www.patreon.com/acservicetech
For those that are looking for the tools used in the videos: (Linked Below)

Here is the link for the Malco Combination snips with 3" long mouth- http://amzn.to/2wuft2L

Here is the link for the Wiss Cable Tie Tensioning Tool- http://amzn.to/2wtYL3D

Here is a link to the Malco Snap Lock Punch http://amzn.to/2cY53Ag

Here is a link to the Wiss 3 Pack Tin Snips http://amzn.to/2bHWhWO

Here is the link for the Wiss Bulldog Snips- http://amzn.to/2x1BeIY

Here is a link to the Wiss 5 Blade Crimper http://amzn.to/2bwTlsW

Here is a link to the Wiss Hand Seamers http://amzn.to/2dRk83v

Here is a link to the Midwest Upright 90 Degree Right Hand Tin Snip- http://amzn.to/2x1TfGZ

Here is a link to the Midwest Upright 90 Degree Left Hand Tin Snip- http://amzn.to/2iSwpvc

Here is the link for the Wiss 12" Folding Tool- http://amzn.to/2xGqb52

Here is the link for the Wiss 18" Folding Tool- http://amzn.to/2wx8y7v

Here is the link for the Wiss 24" Folding Tool- http://amzn.to/2wu6DCg

Here is the link to the Klenk 20oz Sheet Metal Hammer- http://amzn.to/2wxzTpY

Here is the link for the Malco FDC1 Flex Cutting Tool- http://amzn.to/2wwNrlv

Here is the link for the Klein 7/8" Step Drill Bit- http://amzn.to/2xGQVSQ

Here is the link to the Dewalt 1/4" magnetic bit drivers- http://amzn.to/2x1V073

Here is the link to the Dewalt 5/16" magnetic bit drivers- http://amzn.to/2vUYLWV

Here is the link for the Malco Sheet Metal Scribe- http://amzn.to/2eunoU0

Here is the Link for the Malco Dividers for Making Circles- http://amzn.to/2xGN6go

Here is the Link for the Malco Notchers- http://amzn.to/2iRTrlH

Here is the link to the Malco Scratch Awl- http://amzn.to/2vUvmfy

Here is the Link for the Malco HC1 Adjustable Collar Cutter for Drill- http://amzn.to/2vBHxlU

Other tool links can be found in the video description section.

ACSERVICETECH is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.

All of the ACSERVICETECH Playlists- https://www.youtube.com/channel/UCOZR-1IqsAer9wzlvFgb4mA/playlists?view_as=public

If you want to support the ACSERVICETECH Channel and receive more HVAC content, check out http://www.Patreon.com/acservicetech

Skeletor says:

This video is a gem. Thank you sir for sharing your knowledge and experience. 👍

pete eisert says:

A+. Learned a lot. Thank you!

Ruben Cruz says:

Excelente video tanks a lot.

LOLKINGBABY says:

Also you should use bull noses for cutting s and drive it’s so much better

LOLKINGBABY says:

I use the snips the other way around, I think that’s why people call lefty snips righty’s I try to make the scrap where I’d have to pull up on so the disfigurement on the final piece isn’t as bad

Christopher McDonald says:

CANT THE RETURN METAL TRUCK, BE THE SAME SIZE AS SUPPLY.

sav man says:

Great video. Thank you.

JChris Carter says:

See….i never knew what the notches were the clinchdown

Gear Heads Ltd says:

thanks for saving my first day at work

Malia says:

Thank you soooo much !!!

Write a comment

*

WordPress SEO